Replace the pulley if there is a grease leak from its bearing. Check the auto tensioner for leaking and replace if necessary. Is not stricttly nessesary to replace togheter. I hope this help on your question. You didn't say what the history is that has led up to this point so I don't know if you had the cylinder head off and why, so I just have to guess. Apply engine oil to the outer surface of the spacer lightly and then install the spacer to the right counter balance shaft.
Remove the crankshaft pulley, engine coolant pump pulley and drive belt. Is just a few more minutes to remove the Timing belt. If you don't or if the belt breaks while the engine is running you will damage pistons and valves. Install the counter balance shaft sprocket onto the right counter balance shaft and then tighten its flange bolt by hand tightly. Insert a set pin through the auto tensioner body and rod. Most import engines are of that design.
Install the tensioner pulley onto the tensioner arm. Tightening torque Crankshaft sprocket bolt : 160 170 Nm 1600 1700 kg. When exhaust and intake camshaft sprocket is used and install it after checking I. Replace components which are in terrible condition to enable your automobile to run with optimum efficiency and you to cruise with tranquil frame of mind. Install the camshaft sprocket and tighten the bolt to the specified torque. It took approximately 3 hours to change the belt. If the shaft is turned, the belt will be tightened excessively.
Check the belt for oil or dust deposit. Is just a few more minutes to remove the Timing belt. Use a plain washer if there is a plug at the bottom of the auto tensioner. If the timing belt broke while you were driving, there's going to be bent valves and the cylinder head will have to be removed to replace them. Check the belt for oil or dust deposit. If it is installed in the wrong direction, a broken belt could result.
The labor for that job Removing the Timing belt and water Pump. When aligning the timing mark on oil pump sprocket, remove the left plug of cylinder block, and then check that the count balance shaft is in the specified position by inserting the screwdriver Diameter : 8mm, insertinglength : 60mm or more 3. Tightening torque Oil pump sprocket 50 60 Nm 500 600 kg. Using a soft jaw vise , compress the auto tensioner rod. If it is installed in the wrong direction, a broken belt could result.
Make sure you get the timing marks aligned because this is a zero tolerance engine. Make sure you get the timing marks aligned because this is a zero tolerance engine. All you have to do is put everything back in alignment, then slide the belt on. Inspect the Engine seals, cam and crank Replace if need. Check the rod end for wear or damage and replace if necessary. My fiance is changing the timing belt on my car after it died at a stop light. Install the special washer and sprocket bolt to the crankshaft and then tighten the sprocket bolt.
Install the camshaft sprocket and tighten the bolt to the specified torque. Remove the timing belt cover. D mark depending on the engine deplacemeat. On your 2004 Santa Fe. But I recomend replace the timing belt when you replace the water pump. Hyundai sonata questions 2005 hyundai sonata 27l timing belt 3 people found this helpful 3. Insert a screwdriver through the plug hole in the left side of the cylinder block to keep the shaft in position.
Pay attention to the direction of the flange. Be sure to install the as shown in the illustration. Timing belt replacing of crdi engine shema details and timing chehlov. The water pump is not driven by the Timing belt. If the timing belt breaks, the engine will fail to operate. If it is out of specification, replace the auto tensioner. When the engine is overhauled or belt tension is adjusted, check the belt carefully.
If the timing belt is reused, make an arrow mark indicating the turning direction or the front of the engine to make sure that the belt is reinstalled in the same direction as before. Because for get axces to the water pump, you need to remove all the Timing covers. If any of the following flaws are evident, replace the belt with a new one. Rotating the sprocket more than 2 teeth may make the valve and piston touch each other. It took approximately 3 hours to change the belt.
Crankshaft sprocket - Oil pump sprocket - ldler pulley - Exhaust camshaft sprocket - Intake camshaft sprocket -Tensioner pulley 1. Align the timing mark on each sprocket with the corresponding timing mark and install the belt as the following order. Small deposits should be wiped away with a dry cloth or paper. Thank you for use fixya. Switching to new ones enhances Engine performance and proficiently minimizes the risk the worn out component damaging other car components. Because for get axces to the water pump, you need to remove all the Timing covers. All Replacement brand items are backed by 1-year, unlimited-mileage warranty.