At this time, the steering lock will be released. Be careful not to misidentify leakage. Malfunction in inner liquid tank clogged strainer. Remove the radiator core support upper. Never remove the seal caps of pipes and other components until just before required for connection.
High-pressure side is too low and low-pressure side is too high. Disconnect that line and replace the O-ring when the refrigerant leaking point is found. High-pressure side is excessively high and low-pressure side is too low. Exposure may irritate eyes, nose, or throat. Air mix door guide 43. Close the valve to isolate the hose from the pump. Remove mounting nut A , and lower dash insulator 1 to a position without the hindrance for work.
Every single element of service, repair and maintenance is included in this fully updated workshop manual. The refrigerant evaporation in the evaporator is controlled by an externally equalized expansion valve, located inside the evaporator case. Models covered: All Generations and Engines. Install compressor and check the operation. Drain engine coolant from cooling system. Remove mounting bolt A , and then disconnect low-pressure flexible hose 1 and high-pressure pipe 2 from expansion valve. Initially sold only in Japan, the Cube has been sold in North American and European markets since 2009, although discontinued in Europe in 2011.
Clogged or crushed low-pres-sure pipe. All sub-elements have made the journey across the Pacific, and. Lubricant becomes moisture saturated and should not be used without proper sealing. However, if a large amount of refrigerant or lubricant is detected, never perform lubricant return operation. From changing a wiper blade to a full engine rebuild, every procedure is covered with simple step by step illustrated instructions. Compressor malfunction is likely to occur if lubricant other than that specified is used.
Remove high-pressure pipe from the vehicle. Start the engine, and set to the following condition. Lubricant return operation is complete. As of 2014, the Cube is once again sold only in Japan. Eliminate foreign material from expansion valve, or re-place it.
Additional health and safety information may be obtained from refriger-ant manufacturers. It includes absolutely every element of service, repair and maintenance covered within a super user-friendly pdf workshop manual. Sample a compressor oil and judge on the figure. Not even aware of the existence of the previous Cube Ignorance is bliss, and most people with the new Cube looks be delighted. Remove mounting bolts A , and then remove expansion valve 1. Upper air mix door 44. Compressor Intakes, compresses, and discharges refrigerant, to circulate refrigerant inside the refrigerant cycle.
All hoses must equip positive shut-off devices either manual or automatic near the end of the hoses opposite to the manifold gauge. Drain lubricant from removed compressor and measure lubricant amount. The fol-lowing handling precautions must be observed: -Cap seal immediately the component to minimize the entry of moisture from the atmosphere when removing refrigerant components from a vehicle. When remaining pressure exists, recycle refrigerant from high-pressure hose and low-pressure hose. To download free quick-serv komatsu forklift usa, inc. Then apply compressor oil to them when installing. That is, most North American buyers not dorks car, so they.
It is important to always maintain lubricant level within the specified level. Remove mounting bolt A , and then disconnect low-pressure flexible hose 1 and high-pressure pipe 2 from expansion valve. However, if a large amount of refrigerant or lubricant is detected, never perform lubricant return operation. Clean liquid tank and its surrounding area, and then remove dust and rust from liquid tank. Every single element of service, repair and maintenance is included in this fully updated workshop manual. Wear, breakage, or clogging of foreign material in inner parts. As long as the hose is connected, the valve is open and lubricating oil may migrate.
Get the same level of information about your Audi Quattro Sport that your official dealer has. Nissan Forklift Corporation reserves the right to make product changes. Explain any unchecked items at. Replace compressor if specified clearance is not obtained. Repair or replace parts where refrigerant leakage is detected. Collect all refrigerant, evacuate refrigerant cycle again, and then refill it with the specified amount of refrigerant.
Close this valve to isolate the service hose from the pump. Every single element of service, repair and maintenance is included for every production year in this fully updated pdf workshop manual. The styling is still eye-catching, but the last Nissan Cube was the better looking car — a design classic, well. Please contact Nissan Cus-tomer Affairs for further assistance. Wipe it off by using a clean waste cloth moistened with thinner if the surface is contaminated with lubricant. Every single element of service, repair and maintenance is included in this fully updated workshop manual. Technical Information Standard Equipment 1.