The individual relays could be wearing out to a point that the solenoids are not getting enough current delivered to the solenoid for the right duration, hence the magnetics isn't enough to unlock or lock the door. While you are at it, check that the two drain holes in the bottom of the door are clear and there is no buildup of debris there. If it does then only the one lock motor needs replacement. This is a big safety issue, i'm going to lodge a safety complaint and I just got the latest recall so when i go for that i'm going to ask about the cost to fix the driver door. The replacement door lock actuator for Nissan Murano is the electrical component that allows the power door locks to function, without inserting the key into the door lock cylinder.
In many cars, the door lock actuator is built with the latch mechanism into one assembly in the photo. Now, out of warranty and its starting to add up quickly. Park your vehicle on a flat, hard surface. Pull on the inside door handle and ensure that the door opens from the latched position. Ordering new Nissan parts from www. Although the solenoid could be perfectly fine, the relay delivering the pulse of power could be marginal, making it unreliable. Step 6: Remove the lock and actuator assembly and take off the plastic cover.
The hallmarks of a superior car include dependability, strong assembly and a plethora of cutting-edge safety and security equipment, the things you get with every Nissan vehicle. If you know your Year Make Model, put it in the selector so that we can guide you to a product that fits your vehicle. Sometimes I'm convinced that these guys charged single women more than anybody else. My service writer at my local dealership thinks it's worth a shot to see if they will cover it out of 36,000 mile warranty. Like a human body, the absence of one part or system can render your vehicle futile. Sometimes one of the door lock actuator stops working completely.
Pay for only one solenoid and labor. If you think you have seen this actually occur and have witnessed the repair all you have likely really seen is that the initial problem was missed. Start on the corner by slicing your razor through the seam. The driver side handle on my 2002 Altima broke first. When your Nissan needs the best replacement Door Lock Solenoid Actuator, there's no need to go somewhere besides the authority, Car Parts Discount. Most Nissan's and Infiniti's are the same steps. Intermittent as well - but getting worse.
Sometimes it happens in a rainy weather, when water penetrates inside the door lock actuator connector, see the photo. You will also need a good flashlight so you see what you are doing. You should try having only the most important lock fixed, such as the front passenger door. In most cases, the problem with a door lock actuator is limited to only one door. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. This failure is an intermitance of operation.
Then pry the motor up from its plastic portion and pull it out. Select Year for Nissan Altima Door Lock Actuator. What is strange is the problem appeared on the 3 doors all at once - the odds of all three door lock actuators failing all at once are very bad. Carefully pry through the bottom portion next to the pin housing. Install the white plastic cover back onto the lock and actuator assembly by securing it with the two other screws you removed previously. We work hard to build a great website for car parts, so start perusing and see what you find.
When locking the doors it's imperative nobody can gain access at will by walking up to the car. When relays go bad they stop delivering the high current needed for the application. There are a number of options available in addition to generic parts that can provide more enjoyment to your road trips. Sounds really pricy for one door. Use electrical parts cleaner to spray off old grease that has built up on the brushes. This will keep your computer live and keep your vehicle settings current.
It's called the Passenger Side Select Unlock Relay. The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. In some cars, a failed door lock actuator may lock but won't unlock or the other way around. Step 2: Clean and reconnect the actuator. Step 5: Reinstall the clear plastic sheeting.
Remove the worm gear and its bearing from the plastic housing. If the cluster cannot be detached, you may be able to disconnect the harness connectors under the door panel as you pull it off. After it dries, reconnect the black electrical connector to the door lock actuator. I have extended warrentl whent to the dealer and he blaimed it and my aftermarket alarm claiming it was sending close signal to the all locks at all times and burned them out. There are several reasons why a door lock actuator may need to be replaced. Position the actuator on a solid surface and tap the blade with the hammer until it gets in pretty deep.