There were no related recalls. Reverse process for the new bulb. Install the headlight housing into the panel, connecting the electrical connectors, signal bulb socket and side marker socket. Remove the bulb connector from the bulb first, then twist the bulb retaining ring and pull the bulb straight out after the ring is off. Brought car to service center because of a noise in the front of car.
Jan 18, 2013 Well I've found that the easiest way to do it is to remove the headlight assembly, there are three 10mm bolts that are holding it in place, after removing bolts pull the unit straight out there is a clip holding it on the corner but not to worry it's really hard to break. Aug 06, 2010 Hi, You have to remove the headlight assembly mounting screws and remove the headlight assembly. Remove the plastic cover at the rear of the headlamp assembly by rotating it counterclockwise, and pulling it off. Mar 14, 2009 This picture shows the rear side of the headlamp assembly. I had searched a few places locally for a tail light cover for my jeep, and also searched online.
Now that the headlight assembly is out just unscrew the caps to access the bulb. Take off the circular access cover from the rear of the headlight housing. Pick up your durable Hyundai Tiburon headlights from AutoZone and ensure top-notch visibility wherever you travel. Headlights burn out every other month. Dec 05, 2010 I assume you're referring to the bulbs and not the entire assembly: First, you have to remove the turn signal assembly. Sorry this is so long but I figure as much detail as possible will ensure things get done without uncertainty.
During cold weather emergency brake sticks took it in and they couldnt find anything wrong, go figure. After you get them out, you have to play a little bit of a wiggle game with the headlight to actually get it out. All of them face the front of the car. Our dependable staff has information to help with your repair and installation projects, so visit your local AutoZone today to check out our impressive headlight selection. Remove the power cable by squeezing the lock clip to release the cable, then release the bulb from the headlight assembly. Open the hood, find the locking cap behind the light housing and turn it a half turn to remove.
There will be two bolts on the top which go straight down above the headlight and another on the side closest to the middle of the car that is kind of hidden so you may have to kneel down to see it So, if you are working on the right headlight the 3rd bolt is on the left and if you are working on the left headlight the 3rd bolt is on the right. You can even purchase your Tiburon headlight online and enjoy home shipping or take advantage of our Same Day Store Pickup option if you need your replacement immediately. Reattach the plastic cover, and close the hood. The bulb base has three small flanges that seat right into corresponding slots in the bulb housing. It's a simple plastic ball and socket swivel.
Airbag light stays on, past 65,000 so service department wont fix it unless I pay for it. Your Hyundai Tiburon draws attention wherever you drive and offers clean interior styling and affordability. First you'll want to pop the hood open to access the headlights. No one locally had the part because the vehicle was too new, and the online stores had a somewhat high mark-up on their parts. If you're looking to completely remove the entire headlight assembly, it's the same process, but the piece that lets the headlight swing out instead of coming off completely must be removed. Once you have room to maneuver, the procedure for changing the bulbs is exactly the same as for the low beams they even use the same bulbs: H7. The turn signals have also failed.
Seat the new bulb using these flanges, lock the bulb into place with the spring lock and replace the locking cap. Is there a end to the problems that I have with this Hyundai. Let me know, if needed further assistance. I honestly do recommend Go-Parts! Said they couldnt hear anything. Unbolt and remove the plastic panel over the radiator, then use a flat screwdriver to release the clips securing the grille at the bottom to the headlight panel and lift the grill off.
Pull up the retaining tabs for the headlight housing, which are on opposite ends, and carefully pull the housing out. Twist the bulb in a counterclockwise direction, withdraw the bulb with its electrical connector from the housing and disconnect the electrical connector. Reinstall the grille and plastic radiator panel and reconnect the negative battery cable. The windshield washer tank on the passenger side might also give you some problems. Do not touch the glass of the new bulb. Oct 04, 2010 Hello, Please follow the stepwise solution carefully.
Seats wont latch sometimes after letting someone out from the back. Place the socket back into the assembly, and twist it clockwise. The failure mileage was 156,000. Go-Parts had the part I needed, and for a cheaper price. Twist the bulb socket counterclockwise in order to remove it from the headlamp assembly.
Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies see illustration You'll want to disconnect these two connectors. Pull the old bulb out of the socket, and use a clean cloth to install the replacement bulb. Posted on Jan 21, 2009 The 2003 Outlander utilizes replaceable 9007 headlight bulbs. You might need to pull the battery on the driver's side. To get the headlight back in just reverse the process. Open the hood and disconnect the truck's negative battery cable. Since the halogen lights in the headlights dim over time, consider swapping out the headlights before they burn out.