Buyer is responsible for return shipping. Dt is used to properly service the aisin 81-40le planetary ring gear nut. Install the mode actuator mounting screws. Payment must be received within three 3 days of auction closing or item will be re-listed. The auctioneer may or may not honor such adversely affected bid attempts, at Auctioneer's sole discretion. . Use of this tool greatly reduces the labor time.
Remove the screws from the mode actuator 3. All sales are final, and no sale shall be invalidated. Install the transfer case control module to the steering column support bracket. Please ask any questions you may have. We do not ship to po apo fpo boxes, only direct the continental united states lower 48.
These coatings affect fastener torque and joint clamping force and may damage the fastener. This is a non-quoted item and the. I just happened to stumble on to them. If you have any questions please send your concerns to the address available in contact section in the Privacy Policy. Notice Use the correct fastener in the correct location. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. Removing the seal from this disc and installing on existing seal installer J-34686 can damage the inner seal lip.
These coatings affect fastener torque and joint clamping force and may damage the fastener. All of our shoes and pads are perfectly balanced and weight-mated to our Viking pneumatic tools V502 Velcro Type Sanding Shoe for V100 Viking Air Tools V502 Velcro Type Sanding Shoe for V100. Connect the radio antenna cable located near the blower motor. Tighten Tighten the splice pack retaining bolt to 10 N·m 88 lb in. Auctioneer recommends that all electrical or otherwise powered items sold be checked, installed, and or operated by a licensed electrician or other appropriate technician. Remove the screws from the mode actuator 3. Remove the steering column with the steering wheel attached.
Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems. Install the mode actuator mounting screws. Disconnect the radio antenna cable located near the blower motor. The Bidder assumes full responsibility to inspect and to evaluate the property to its, his, or her, complete satisfaction prior to any bid or purchase. Tighten Tighten the lower steering column support bracket bolts to 50 N·m 36 lb ft.
The following terms and conditions apply to all auctions conducted by United Country Heard Auction and Real Estate, it's employees, agents, and assigns Auctioneer , and any participants, their employees, agents, and assigns Bidder , in said auctions, unless otherwise stipulated by the Auctioneer within any additional terms and conditions specifically expressed in regard to any single auction. Install the upper and lower bolts retaining the steering column support bracket to the left cowl side carrier bracket. Now the Mode Door Actuator can be serviced from underneath the left side of the Instrument Panel Carrier using this new special tool. Lots originating from different auctions may not be aggregated for sales tax purposes. Connect the mode actuator electrical connector.
I was able to fix this be replacing the mode door acuator. Previous to the release of this tool, it was necessary to remove the entire Instrument Panel Carrier to replace the Mode Door Cam Assembly. Refer to Steering Column Replacement in Steering Wheel and Column. Bidder agrees, in compliance with the Consumer Product Safety Improvement Act, to buy vintage items as collectibles for display purposes only, and with no intention of using them, selling them to be used, or of allowing them to be used otherwise. Install the center bolt 1 retaining the steering column support bracket to the left cowl side carrier bracket. Designed to protect expensive engine cases by using a specially designed support block to remove or install cam side crankshaft bearing. Kent-moore dt a driveshaft remover adapter chevy equinox genuine oem special service tool just like the dealerships use.
After purchasing, pay instantly with your credit card through PayPal! Fast delivery service , correct part , excellent prices. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. Replacement fasteners must be the correct part number for that application. Install the splice pack to the floor panel. Manufacturer drop ship; please email for cost and lead time. The technician will pull the actuator off of the shaft that engages into the cam.