There isn't any plastic on it and it bolted on perfectly. The starter housing itself fit the recess in the bell housing percisely. Once the nut is off, we'll remove our ground strap, and allow that to hang off to the side. Once you've located the 13 millimeter nut, remove it with the socket and ratchet. Advance Auto Parts has 40 different Starter for your vehicle, ready for shipping or in-store pick up. And really you owe me a starter reimburse for having to buy another so I would be pleased if you would send me a store credit for my other starter I exchanged for core charge on this New starter.
Aside from that it works fine. Took one star off because of solenoid connections. In this video we're going to be working with our 2001 Ford Ranger 4. Make sure you don't kink any wires in there, especially the ground. Here are the items you'll need for this repair. Our units are remanufactured to the highest standards for unmatched cranking performance. This starter is pretty much identical to the Visteon Ford starter that it replaced.
I tried with the car jacked up at driver's side wheel and with the tire back on and truck on the ground. Tighten the clamp back up. So I paid for another one and have the receipt thumb tacked to my wall waiting to get another starter in a couple months. Disclaimer: -Some of our units used engine, transmission, axle, etc. The original auto part must be returned using the provided shipping label.
With thousands of part numbers in stock, we have the exact starters for your vehicle. Again, with these are in such a tight spot, go ahead and get those down as far as you can by hand before trying to tighten them up with your 13 millimeter socket and ratchet. Generally there are discounts available that are not available in the store I can order a part on line and go to the store where it is sitting on the counter waiting for me when I arrive. The shipping cost for both the original and the replacement auto part is a cost attributed to the shipper at hand. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Submitted 2018-04-23 By William From undisclosed It seemed to fit perfectly and it worked the first time I turned the key.
Also ease of installation has to be due to engineering of the vehicle in the manufacturing process in that there were no issues with having to remove other components to gain access. It typically takes us approximately 3-5 business days to process a credit back to your account and 2-3 business days for the credit to appear on your account. Bottom Line It seemed to fit perfectly and it worked the first time I turned the key. We'll then install the 13-millimeter bolt at the top. This red cap simply pops off.
It was more noticeable when the car was cold. It works and fits perfect. The 13 millimeter nut is located all the way at the top of the starter solenoid. This picture just shows it parked, where I left it last night, between the front drive shaft and crank case. Your starter is located on the driver's side of the engine, bolting in from the engine side into the bell housing on the transmission.
When it comes to your Ford Ranger, you want parts and products from only trusted brands. Great site and service thank you Bottom Line recommended This product was advertised as an exact replacement which is exactly as advertised very easy to install due to not having to make any modifications to the product. Both provide exceptional performance and exact fit. We do not require a core charge or a return of the old part or engine. I had replaced the belt, so I knew that wasn't it.
Even in the harshest conditions, Carquest starters get your engine going. Then we'll finish tightening that up as well. Please note: This starter is built by one of two world-class vendors. Just be sure you have the right one they look almost identical. Would I buy again, yes. We're going to use an 8-millimeter socket and ratchet, or you can use a wrench.
Unfortunately, this is just in a really tight spot. Every starter is exactingly bench-tested to ensure factory-original performance. The largest one going on the top terminal, and being secured with a 13 millimeter nut, and the signal wire will be secured on the side there with a 10-millimeter. Make sure your connection is tight. The part was ordered via the web site which has turned out to be my go to place when I need parts. The bolts can be found at a hardware store for around a dollar each.