Install the J 21474-18 1 , the thrust bearing 2 , the J 33791-1 3 , the J 36616-2 4 , and the forcing screw as shown. Tighten Tighten the inner axle shaft housing nuts to 100 N·m 75 lb ft. Wasn't too bad to do, if you go to get the parts the parts places around here had it listed as the inner axle bearing and outer axle shaft seal just for reference. Hear from other customers via the 1,051 reviews on parts for your Chevrolet Silverado 1500. Install the J 29369-1 1 behind the inner axle shaft bearing.
Differential Carrier Assembly Replacement Removal Procedure 1. The clutch fork assembly 11 8. Disconnect the electrical connector from the electric motor actuator. Install the clutch fork assembly 2 into the inner axle shaft housing 1. Connect the wire harness to the inner axle shaft housing. Not using the parking brake once the vehicle is parked will cause transmission wear.
Refer to Lubricant Replacement - Front Drive Axle. Once the lubricant wears out due to mileage or abuse, they can start grinding and vibrating. Clean the area around the front axle fill plug and the drain plug. The thrust washer 5 12. On top of low prices, Advance Auto Parts offers 6 different trusted brands of Differential Bearing Kit products for the 2007 Chevrolet Silverado 1500. Notice Refer to Fastener Notice in Cautions and Notices. I asked for the manager and after rehashing the account, was still not able to get results.
No one could understand what I wanted. Tighten Tighten the inner axle shaft housing mounting bracket to frame nuts to 90 N·m 67 lb ft. I have a 2001 Z71 extended cab with a 5. Install the assembled axle tube and the shaft to the carrier. Remove the differential carrier assembly upper mounting bolt and the nut. Remove the air conditioning compressor- 4.
The clutch sleeve 8 7. Install the following components into the inner axle shaft housing, 8. Disconnect the wheel drive shaft from the inner axle shaft. Install the stabilizer shaft link assembly. Tighten Tighten the wheel drive shaft inboard flange to inner axle shaft bolts to 79 N·m 58 lb ft. Check listing to insure that you have identified the correct front end.
Refer to Sealers, Adhesives, and Lubricants. Step 3 — Remove hub The hub is the piece to which the caliper was attached to and which has the main lugs where the wheel is mounted. Remove the inner axle shaft housing bolts from the differential carrier case. Fill the differential carrier assembly. Front end parts are available for the popular 9. Place the differential carrier assembly into a vise.
Remove the stabilizer shaft link assembly. . Keep in mind that in the Silverado, the bearing is sealed in the spindle assembly, and the whole part may be replaced. To place an order please call the order at 888-824-2012 or toll free. Using the J 34672 , measure the distance from the edge of the front drive axle clutch gear to the machined flange surface of the inner axle housing. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Measure the torque required in order to rotate the pinion.
Included all seals, Timken bearings, and sealant. Remove the front axle fill plug 1. Refer to Differential Carrier Assembly Replacement. Should you choose to rebuild your own 8. The clutch shaft shim 9 4. Support the differential carrier assembly with a transmission jack or equivalent. Remove the differential carrier assembly.
Place jack or utility stands at the rear end of the vehicle. Remove the yoke retainer bolts 6 and the yoke retainers 7 from the front axle pinion yoke 1. Refer to Lubricant Level Inspection - Front Drive Axle. I had my front driver's side axle replaced about 6 months ago when a u-joint broke inside the boot. The only other options are my wheel bearing or my front differential so I was wandering what your opinion was on it and if there might be a bearing in the front differential that might be bad. Install the front differential carrier assembly.
I didn't take the ties off either. Remove the inner axle shaft from the inner axle shaft housing. Disconnect the wire harness from the inner axle shaft housing. Refer to Lubricant Replacement - Front Drive Axle. Refer to Lubricant Replacement - Front Drive Axle.