So, I have a question about an 87 Honda Accord. How to remove the evaporator on your Honda 1-evacuate ac system of 134a, 2-discoonect ac lines at firewall, 3-remove glove box door and glove box 4-Disconnect fan motor and remove 5-disconnect all connectors on evaporator housing 6-remove bolts holding evaporative housing to firewall 7-remove evap. If you're careful, you can do it in an hour. You will probably need the extension for the socket wrench. It is on the passenger side of the engine near the bottom, underneath the air intake tube. You may have to move the air intake hose out of the way. Find out how to repair it here, and keep yourself warm in the frigid temperature.
You will also want to remove the fan switch, which is easy to disconnect. I don't know anything about cars but I know this fixed my problem. There are embossed arrows and the words Open and Lock on the ring and grip ridges along the side. Once the gurgles stop, tighten the bleeder bolt and fill the radiator as needed. I don't know anything about cars but I know this fixed my problem. It is on the passenger side of the engine near the bottom, underneath the air intake tube.
You will need… Drain about 1 gallon of coolant from radiator. I finally stopped by the dealership when the tachometer was jumping and they were able to diagnose the problem. The 1998 Honda Accord was available with two different engines---a 2. The two 10mm bolts holding the thermostat housing in place might be a tight fit for your wrench. So why not take the unique route, and install a supercharger? Once you have nudged it loose, continue to nudge the actual thermostat loose from the thermostat housing. Also, consider gently squeezing any radiator hoses that you can reach to coax any residual stuck coolant out.
Step 2 — Remove air intake On the front and back of the air intake box there are 10mm screws. You will need to do this so that when you remove the thermostat, you wont have coolant spilling all over your engine bay and driveway. Pro Tip The removal of the air intake is generally needed to gain access to the thermostat; however, if you feel like you can gain access without removing the air intake, feel free to skip it. The official procedure is… The thermostatis in the water jacket at the gearbox or right hand end of the engine block at the top, follow the top radiator hose. This article applies to the.
Unplug the mass air flow sensor, so that you don't pull on it by accident. It is mounted under a panel that makes up part of the floor. The by-pass rivet the floating pin on the flange of the thermostat is located between those holes. Posted on Jan 04, 2010 I had the same problem with my 1995 Honda Accord V6 2. Remove the screws that are holding it in place. Take note of the parts surrounding the air intake that you will need to disconnect.
There should be a large hose running into it from the radiator and an electrical clip on top. AutoZone has the thermostat replacement for Honda Accord you need, plus free battery charging and engine diagnostic testing at your store visit. You'll have to do a little bit of digging to get there, but it's not bad and can be done with normal tools. I would install about 3 quarts after draining,and start checking the level at this point. Lastly, the throttle cable might be clipped onto the intake tube, so undo that. Once you remove the housing, you should be able to take the thermostat out.
First get the top bolt in, but wait to tighten it in order to secure the bottom bolt. This tube is fasten to thermostathouse. It's in three… The thermostat for the 90-93 accord is on the back left-hand side of the engine where the hose connects from the radiator to the engine, disconnect the hose and clamp it off or move it to the side as not to leak antifreeze use a rag or container for antifreeze that comes from engine block. An important part of a car's cooling system is the thermostat. Usually the black locking ring is stuck from years of road splash, so you might have to stick… Repalce the burned out fuse from the fuseboxpull the hood release down by your left foot sitting in driver's seat.
By - March 20, 2015 This article applies to the Honda Accord 1990-2002. Removing the 10mm bolts around the edge of this panel will expose the larger engine control module and the smaller transmission control… I just did this on my 1995 Honda accord ex, so here it goes. If you suspect that you need a thermostat replacement, then be sure to read this article. Remove one bolt that is tightened around some hoses to access the bottom of the housing. Learn how to do just that. This article applies to the Honda Accord 1990-2002.
It should be replaced when the cam belt is replaced which must be replaced every 90,000 miles. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Find the bleeder bolt on the right side of the thermostat housing should have a hole in the top and loosen it. I'm using basic terms because I don't know what everything is called. Reinstall the air intake and be sure to reattach all of the hoses I only took off 2. Unbolt the window and replace the motor the way it came out.