Timing belt failure may result in either the intake or exhaust valves bending after contacting the pistons. Posted on Sep 20, 2010 The Honda F23 series engine is a 2. Squeaky belts are annoying, and should be repaired before actual damage occurs. With all the timing marks lined up, route the new belt around the largest diameters first, leaving the smallest pulley or sprocket for last. Now that i have the proper instructions to tension the belt correctly, the marks wont stay align when i turn my engine by hand while tensioning the belt. Akismet This is used to detect comment spam. Temporarily re-attach the Balance Shaft Tensioner puller and hand tighten the Tensioner Bolt.
Remove the jumper from the service connector and replace the rubber cap to the inspection window. Step 23 Rotate the crankshaft pulley 5-6 turns counterclockwise. It was as if someone had turned off the key. Remove the rubber cap from the inspection window of the cylinder block. Apr 01, 2009 hi the balance shaft has to set by removing the bolt in the engine block that is in line with the front of the balance shaft the get a 6mm bolt that is 100mm long slide it into the hole where you revoved the bolt turn the balance shaft keeping a slight pressure on the bolt until it locates the hole in the shaft and locks it up then if you look at the oil pump there is a mark on the top of the housing and the oil pumps shaft just line them up stick your belt on tension and remove the locking bolt yates210456 Oct 10, 2008. Each belt is manufactured from quality synthetic polymers to provide resistance to heat, stretching, belt shear, climate conditions, and abrasion to assure dependable operation throughout the belts service life. While a well worn cylinder will leak about 20%.
I set a spare car jack so that the breaker bar end of the extenders rested at the same height as the crankshaft bolt so that it would keep all the torque in the right direction and not twist out of place while turning. Measuring Compression on a Honda To measure compression, you need a compression gauge which has a hose that screws in place of the sparkplug into the engine. Reverse removal procedure to complete installation. Otherwise low compression readings will occur. The wheel is off anyways and it is very easy to turn. They are equally important, and require special attention that requires advanced mechanical knowledge.
Special Tools: Since the F23 engine rotates counter-clockwise and in the absence of impact driver that generates over 150lbs of torque, a Honda Crankshaft Pulley Holder tool must be used to keep the pulley from moving when attempting to relieve tension on the Crankshaft Pulley bolt. I failed ignition timing because i set the ignition timing pointer at the red marking. Make your marks if necessary , then remove the belt and balancer. You need to count the teeth. I had problems with the tension part of my car and I can't adjust it properly til you provided this detailed steps. If the Water Pump is leaking through the weep hole or the bearing seems worn, replacement is advised. I hope help you remember rated this help Good luck.
Look closely at the crank damper and pulley for separation. While you're in there, there are a few other important things to address like the timing balancer and the water pump. For those that are too lazy to look it up, there is 47 valleys between the belt teeth from the crank gear dot to the exhaust cam dot. Aim the timing light at the hole of the Timing Inspection Plug and the light will flash only when the 1 cylinder is firing. They are independent publications and are not affiliated with or endorsed by or.
Next, Jack up the front of the car and support it with jack stand and remove the front drivers side tire. This recessed channel is needed to lock the balance shaft in place. Careful consideration should be taken when installing the components because you will need to ensure timing is set correctly as previously marked. It looks like a mini oil filter It will be much easier to change if you remove the vacuum control box first so that you have easier access to the bolts for the fuel lines. It looks that there should be a identifying plate to the left side of the window with the numbers 24 with a line and to the right side is the pointer. Remove the pump from the engine.
What worked for me: After taking off the left front wheel driver's side and plastic shrouding: On the front pulley there were 6 holes. Other product and company names shown may be trademarks of their respective owners. This is a small, blue, two-wire connector positioned next to the larger blue diagnostic test connector. For the one with the pin, just use a drill bit shaft that seems to fit the best and look for the marks. The figure shows a cap blocking… First set the crank shaft gear inline with its pointer or timing mark and do the same with the oil pump, as for the cam gear set up there are two marks.
There are two compression checks made: dry and wet. Next, loosen the 14mm or 15mm bolt which secures the 2 belt tension wheels. If no high torque impact driver is available, and assuming the Honda Crankshaft Pulley Holder Tool is on hand, secure the tool in the pulley. For the crankshaft below, there probably will be a timing mark on the damper pulley that lines up with another mark on the lower cover. Please elaborate as I am not familiar with the term ignitor on a gasoline engine, and do not understand what you are referring to. Additionally, the face of thefront timing balancer pulley has a mark which must be aligned with thenotch on the oil pump body.
Remarketing Pixels We may use remarketing pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to advertise the HubPages Service to people that have visited our sites. Use a special tool that fits inside the hex on the crankshaft damper and a long breaker bar to remove this bolt. If that is so, maybe the spring loaded when line the marks up, and after rotation they unload back into the rest position causing the mark to be incorrect. I don't trust my crank gear notch because it isn't exact. Timing belts and water pumps are wear items.