Questions I put about a quart of fluid in the new torque converter and spun it on till it clicked down about 3 times, its at the same position it was in prior to me removing it to fill it. They also come with a varying set of rules. Mark i will look into that today i have no problem doing it i did my transfrercase already i have all the bolts of the trans ill get it done today thanx for the help ill post how it goses You do know that the converter has to come off and back on with the transmission. The Chevy Silverado 1500 transmission system soon came standard as an automatic six-speed on all 2010 models, though. Is It Possible to Replace the Transmission Fluid On Your Own? Yes, that is how you know the converter is mounted correctly, there should be a small gap, then you pull the converter to the flywheel. When disconnecting hoses and cables, make a drawing showing how each one is routed. Refilling Refill the transmission based on the recommended procedures.
This article applies to the Chevrolet Silverado 1500 2014-present. The shift linkage attaches to the transmission with a single bolt and nut. If the front of the transmission is allowed to tilt downward, the converter may slide out of the transmission and fall hard to the floor. The dealership has a bulletin on transmission cooling that this is a manufacture defect. Something's not right under the hood, but what could it be? The Chevy Silverado is a force to be reckoned with, combining powerful towing capacity with enhanced fuel economy and the latest technology, but without a good transmission, no car can operate properly. Guy who sent the trans gave me all new bellhousing bolts so Im golden.
Just getting rid of the muffler won't hurt it at all. Line up the torque converter holes with the holes in the flywheel. They even said never purchase a vehicle made on monday or friday. The fittings will leak if these washers are not replaced. The bulbs are not replaceable and that's simple just 4 hex screws on the corners. Common Symptoms of a Failing Transmission Fluid When to Change Transmission Fluid For instance, your manual tells that you need to change the transmission fluid of your Chevy Silverado at 100,000 miles.
How to Change Transmission Fluid Chevy Silverado 1500 Steps Step 1. Having to remove parts of the exhaust after the transmission is separated from the engine is much more difficult. Park your vehicle on a flat concrete surface, put the shifter in Park, set the emergency brake, pull the hood latch and then open the hood. Step 3 — Remove dipstick tube bolt The dipstick tube is bolted to the engine with one bolt. If none of this works, depress the park brake pedal a couple of… the same way you would change the wheels on any other vehicle.
Keeping nuts, bolts, washers, clamps, etc. Continue wiggling the torque converter and rotating it back and forth while pushing in until it is fully engaged. Do I need to do anything to the dipstick tube when inserting it into the trans? Cars or vehicles has always been a passion of mine and will always be my favorite pastime. Remove any starter bolts that are accessible. This type information can be easily found in your owner's manual. This article applies to the Chevrolet Silverado 2007-present.
Also check the dowel pins on the engine and the dowel pin holes on the transmission as they also must be clean and free of burs. Re-install the transmission pan when you are done. Removing the transmission mount bolts or nuts allows the transmission to be separated from the cross member. Still working under the hood, locate and disconnect any transmission electrical connectors you see. Install one bolt but do not fully tighten.
Start the engine and with the brake pedal depressed, move the shifter through each of the gears a coupler of times and then place the shifter back to the Park position. It is not abused and has been serviced on time. This article applies to the. Unlatch both rods out of their retainers and pull them straight up and the assy should come out… First block the wheels to keep the truck from rolling. Clamp them on the tube as far down as possible, and then try to twist as well as pull to get it out. Note: The fluid will need to be drained from the converter regardless of whether you plan to reuse it or replace it. Also, when pulling the lines out, be careful not to lose the thin metal washers.
For example, a 2005 comes with a 6. These are usually more difficult to remove because there is very little space. Burnt fluid and leaks are also signs that your transmission needs to be serviced. It takes time for vibrations, corrosion and things like that to damage them. The four bolts that attach the torque converter to the flywheel are accessible from underneath the Silverado where the engine meets the transmission. I searched all over and couldn't find anything so i decided to try myself.
I searched on line and found the problem has been going on at least since 1999. Bell housing is between trans and engine. Repeat until they're all removed. It may be a common problem but using a torx instead of a torx plus makes it much worse. One of the main issues here is over tightening seals.
The job of removing and replacing an automatic transmission is not tremendously difficult - it's just a matter of being prepared, being safe, and following instructions. Also, keep in mind that once the transmission is removed and lowered to the floor, the vehicle must be high enough off the floor to allow the transmission to be slid out from underneath the vehicle. It is stuck in the dowel pins and needs to be pryed off with a prybar. Chevrolet manufactured the Silverado line of pickup trucks for almost 40 years. So far so good, new trans is showing up tomorrow. This is the first time at removing this, where would this bell housing be at, and where would the bolts be, the manual didn't mention this at all. The crank for the window aslo has to be removed.