Make sure that the button is in the off position as the a The 2010 Ford F150 is a large cargo truck that has both front and rear seating, with the rear seats removable for extra space. I am about to begin a full blown audio system instillation and need to gain access to my rear wall in order to mount my amplifiers. Especially when it comes to removing that dreaded rear seat back. The key to sliding the rear seat, the seat and the back must both be vertical. The article you are referring to using the screw driver is one of the three articles I used today too. That portion see red portion of clip in my install article was very flexible. This is what we did to make it as … easy as possible 1.
Remove all ten of the se Removing the back seat of your Ford F-150 Super Cab will involve removing 10 bolts that hold the seat to the back wall of the truck and the floor board. Push on them and pull the seat up and out. The taillight assembly is removed by:. The extended cab allows room for a jump seat or storage in the back, but is not large enough to install a car seat. Pull the seat cover up from the bottom of the cushion to expose the mounting brackets and bolts that secure the seat backs to the vehicle. Step 4 Remove the four mounting bolts with a socket and ratchet then lift the seat backs out of the bracket.
Replacing the back seat in a 2005 Ford F-150 Super Crew Cab truck is necessary when you need the extra space in the back compartment for other equipment. Excessive wear from children, pets and workplace environments can be mitigated with a seat cover. Slip light assembly back in and replace the 2 screws. Below I show two examples of where you need to get a grip on it with your finger. I continued to try to do this for about an hour. Tighten the bolts to 18-32 ft. I inserted a paperclip into the pinhole, and it released the locking mechanism on that side so that the headrest could pop right off.
Ifyou have a split folding rear seat, you need to open the truck andpull the left and right straps to unlock the seat backs. Rare features included seat memory, and seat heaters. With the headresat down you can feel the locking piece that retracts when you lift the headrest. I usually jam something under the seat cushion after released to keep if from catching again. But I then got stuck on the middle connector looks like a peg that you'd just lift the seats out from. At the same time take your free arm and push the seat down not very much effort is required Keep pushing the screw driver,.
There is enough room to mount your amplifiers, tv tuners, or anything else you wish to the back wall. You probably noticed the obvious on that sticks out of the side of one of the rings. Click release at base of headrest and pull up 2. For that reason, if you are installing a car seat into your truck, it will need to go into the front seat. I was able to reach around and grab the plastic release clips or so I thought. You should hit resistance, move the headrest and paper clip around and the headrest should release and slide out.
Only 12v and ground are needed to power them up. Examine the plastic covers the headrest posts stick out of. This how to will be helpful for anyone. I am providing this information to you so you have a basic understanding on the process. Even tried a new alternator and the battery light still stays on. Dec 27, 2010 On my F150 2002 model , there is only one release button.
I bought some King Ranch Seat Covers I wanted to put on my 2006 F-150 Super Crew, For the bottom part of the rear bench seat on the 2006 F-150 there's 4 star bolts on the sides that aren't too tough to remove. It is very obvious what you have to do once you are looking at it. This is what the plastic clasp is grabbing on the seat. Difficulty:EasyInstructions Grasp the seat belt buckle firmly in one hand. If the seat bottom is not locked in the upward position the seat will not move. Difficulty:Moderately EasyInstructions Things You'll Need Socket wrench Socket set Open the back door on either the driver or passenger side. The headrest has on obvious button to adjust the height and another button kinda hidden to remove the headrest.
To remove either of the split rear seat. It's a real pain to take out a seat that is stuck because it's on the wrong side. The other articles work too, but I found them less than easy to understand. Pry top plastic cover off of the middle seat belt at the top of the seat. Finally, pull seattoward the center of the car to disengage the outer pivot bolt andremove seat from vehicle.
I didn't figure that part out and just reinstalled the star bolts I'll reattack this project another time. Turns out, its a two pieces clip and I was only grabbing the rear portion of the clip. All you have to do, is pull the pins towards the front of the car and then lift the seat out. You will have to press on the spring to put the head rest back in also. Need to install new carpeting, install sound dampening material, have to much time on your hands, installing a sound system, upgrading seats, or whatever you have in mind, this will help you out. They are located on the floorboard just below the seat. Ste … p 2 Remove the retaining bolts with a socket and ratchet or wrench.