There are two 10mm hex head nuts that secure it. Be careful not to pull on the wires but pull on the plastic connector. You can turn off each player by ejecting, the cassette tape or compact disc, audio system was previously off, then, entire audio system will be turned off. Each connector has a tab you must press in, in order to slide out the connector. Make sure the stereo mounting brackets are set down onto them: Make sure the bracket sits down over the post circled above Step 9: Reconnect the center speaker and reinstall the 2 bolts.
Then my husbands car, same make, model, year had teh same problems, and they told him it was his compressor. There is an official tool for doing this but my official tool is an electrical-tape wrapped flat-head screwdriver. Whether your an expert Toyota Sienna mobile electronics installer, Toyota Sienna fanatic, or a novice Toyota Sienna enthusiast with a 2004 Toyota Sienna, a car stereo wiring diagram can save yourself a lot of time. There are 4 10-mm headed hex screws on each of the two brackets. I thought the battery had failed as I had never changed the battery since I bought the van new. It has a shielded auxillary audio cable to go into a small hole for the ipod to playu and the phone to go through the speakers.
A week later, I came back, frustrated with cooking in the car, I told them to check the compressor since they had replaced it on my husband;s car for the same symptoms just recently. I thought maybe the alternator has failed. Step 6: Disconnect the wiring from the stereo. Thanks for the write up! To preset a station to button: Tune, until you hear a beep—this will set, to recall a preset station: Push button. Remove the left and right radio mounting brackets to install on the new stereo, if necessary Bracket bolt locations Step 7: Connect the wiring to the replacement stereo. I decided to drive to Atlanta and have the alternator fixed in Atlanta. Z Never try to disassemble oil any, not insert anything except a compact disc into slot, details of specific buttons, controls, these buttons are used preset.
They fixed the battery but told me that the battery wasn't charging. Toyota needs to stop contracting with them. I am out of the warranty period and so Toyota won't fix it for free. So I took the next exit and went to Walmart to fix the battery. It came time to swap it out. The mechanic initially replaced the compressor but later came back and stated the entire system needed replaced because the condenser has been contaminated and destroyed when the compressor blew up.
I will never buy Toyota again. Information may not pertain your system, your audio system works when ignition, for details about your system's tone, your vehicle has the mast type antenna. Based on what I read online, I'm just worry that if I fix it now, the problem will re-occur in the near future. Use of the Toyota Sienna wiring information is at your own risk. If you want some real non-abrasive interior panel prying tools you can get them. One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 2004 Toyota Sienna. As you are putting the stereo all the way back in place be aware of the antenna cables and wiring harnesses to make sure they have room.
The left panel has two wiring connectors and the right one only has one. The 5 connector locations on the back of a Toyota Sienna Stereo Model A56828 And the connector tab locations are marked with arrows below: Stereo wiring connector release tab locations Dash with stereo removed Step 6: If necessary, transfer the bracket from each side of the old stereo to the replacement. These 4 screws hold the stereo in place via the bracket that is screwed to each side of the stereo. If you need a 10-mm driver, get one. I simply searched for the number on the front corner of the stereo, A56828: Model number on top left of stereo Label on top of stereo: Toyota Stereo Model No. As the weather warmed up again, I used it, and it was only blowing hot air. Removing the center channel speaker Center Channel Speaker 10-mm nut head bolts Disconnect the speaker wiring harness.
By June, the failure was constant. Insert the near side with the tabs down into their slots and then press the back side down. Before Chattanooga, the battery light came up and I heard a 'wee' sound - didn't know what the sound was. One thing to note is that there are two tabs on the speaker that fit down into a notch in the dash so be aware that they must line up: Tab on the speaker that fits down into a notch Step 10: Reinstall top center channel speaker grill panel. So much for Toyota quality!!! Fact, different kinds music vocal, programs usually sound better with different mixes of treble, midrange bass, a good balance of the left right stereo, channels and of the front rear sound. Automotive wiring in a 2004 Toyota Sienna vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics. Took it in - delaer charged me 100 and said they could not find anything.
By the time I got to the Atlanta suburbs, it became dark and I had to switch on the lights. The said freon level was low, there's probably a leak, they sadi we'll refill it, then drive for four days, then bring it back so they can identify the where the leak is. When you insert cassette, exposed, do not insert anything other than cassette tapes into the slot, tape, when you insert a disc, gently push it, automatically eject a disc label side. Thanks in advance for any help you can give me. So now the compressor failed again. The Modified Life staff has taken all its Toyota Sienna car radio wiring diagrams, Toyota Sienna car audio wiring diagrams, Toyota Sienna car stereo wiring diagrams, Toyota Sienna car radio wiring schematics, Toyota Sienna car wiring diagrams and cataloged them online for use by our visitors for free.