You will find the two tensioners for the two belts. My daughters 2001 Pathfinder is experiencing some strange problems. Hydraulic lifters will rattle a little when the engine first starts if the oil has leaked out. I just solved the problem for my 2004 nissan skyline 250gt. Took it into my Mechanic and he replaced the solenoid that operates this valve.
I even cut off some ends re-connected where there was cracking. Either it was finding the correct lube, or figgitting around a little bit everywhere. I am not sure if there is a spring that is supposed to hold it in the open position. Peel back harness to get access, repeat steps for plug remove install. Install plugs torque 14 to 21 ft-lbs and coils. I will try and change the fuel regulator and fuel dampener this weekend. Next some reading told me to blow out the vacuum lines with air--they get clogged up.
Piston slap takes a little longer to go away, and that's because it's a noise that's caused when the skirt of the piston pops from one Sid of the cylinder to the other. Funny that the problem always seems to occur after removing the air intake piping. Being a 2001 model I would replace the engine coolant sensor anyways and with summer coming on a flush and refill of the coolant is not a bad idea either especially if you cant recall when it was last done. Or why the problem remains? Defective swirl control valve control vacuum check switch. If you experince this problem. When driven the vehicle cannot maintain smooth operation and surges over 2500 rpm, sometimes going over 5000 rpm.
I applied direct power to the solenoid itself and the actuator does shut from the open position but what is it that makes it open? Given that, the likely cause of failure is the plunger getting gunked up and not moving. Frankly, the manual is confusing. Clean throttle body with carb cleaner and toothbrush, 100,000 miles mine was very dirty. Also after applying the pentrating oil the actuator seemed to have a little more. As the engine warms, the piston expands and usually the noise either goes away or diminishes considerably. Then press the button on your remote to program it. A woird to the dumb would be awesome.
Unless there is a line that I am not aware of I don't think this is the problem. Clean the hose, and, apparently, problem solved. I have ordered the Swirl control solenoid valve, check switch, fuel pressure regulator, and fuel damper. Don't know by unpluged the hoes if regular air from in my garage can cause the swirl control valve to go inoperatble. Two small nuts are holding it in place. Pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness spiral cable, the Supplemental Restraint System consists of side air bag module located in the outer side front seat , side curtain air bag module located in the headliner side of front and rear seat , satellite sensor, diagnosis sensor unit one of components of air bags for a frontal collision , wiring harness, warning lamp one, of components of air bags frontal collision.
You may have to before you can post: click the register link above to proceed. I took it to Autozone and they ran a scan. Since you do not have code, I'M thinking that you might have something defective within the sensors needed that would not raise a code if defective. I started by lubricating and freeing the actuator itself after reading other people with a similar issue and I can manually move the actualtor freely to the open and closed position with no significant resistance which I am not sure it is supposed to do. Also check circuits and wires to be sure they are ok.
Once all your screws are out you will pull on the door panel to remove the plastic clips behind the door panel. Refer to engine control manual. I'm wondering if your part is what I need for my 2004 Pathy. What was the model number for the valve for your 2004 v35? I too have a p1130 code after washing my motor at the car wash. Under there is a metal box with a sticker on it. Chuck Thanks, I did check if the hoses were hooked up vice a versa and recheck if it is cloged, looks clean and the correct way connected, I guess it's just a co-incident but I did order a swirl control valve through the dealer dealer item only and have them install and clear ses light. You have easier access if the oil filter is removed.
I took the air intake back off and double checked for hoses off and air leaks. What is making it stay shut? Have P1130 code Greetings all. I can not seem to figure this out and I really could use some help on where to go next with this besides the dealership. Great simple process carlsbad Howdy. After ordering and installing the new swirl control valve I still had the same issue. I am getting no codes whatsoever.
But one way to determine if a car has one is go to a few parts sites, like Rock Auto, and look up a timing belt for a 2002 Pathy. Let us know after you install the swirl control valve and fuel pressure regulator. Difficulty level low, take your time. Make sure to replace the grommet. Rattling sound in the engine when rev between 1. I reset the code but it came back in about 150 miles later.