The engine braking system is so strong that Active Decent Control doesn't even seem necessary. . Wash the pre-filter in soapy water, then rinse and let dry. Practice on smaller hills before attempting larger hills. If loose nuts and bolts are found, see your Polaris dealer for service before operating the vehicle.
Practice turning at slow speeds before attempting to turn at faster speeds. Proceed at a steady rate of speed and throttle opening. I did that yesterday and was able to get get reverse to stay but no change with forward. It has a hydraulic, all-wheel lock for a parking brake. Servicing Date Dealer or Person Remarks. See page 117 for the part numbers of Polaris products. Start the engine and let it idle for 20-30 seconds, then stop the engine.
Improper procedure could cause loss of control or overturn and result in serious injury or death. So, click your model, check out the diagrams, and get your parts. We also carry a large selection of. If you need your orders quicker, please give us a call at 855-542-1616 and we will give you our expidited shipping options. Maintain a high level of alertness, reading the trail and avoiding quick, sharp turns which can cause skids. I think it's going to get ugly but I hope not. Carb job went fine and runs like a top until I put it in gear it went about 2 inches and popped out back into neutral.
The crankcase hose goes to the stock air box. I guess short of buying a maintenance manual. Never remove the pressure cap while the engine is warm or hot. Use caution when applying the auxiliary brake. If you cannot locate this card, or if it has been removed, please call 1-800-342-3764 for assistance. That's without moving, shifting or changing anything. Always allow the engine to cool before removing the pressure cap.
Fuel Valve The fuel valve 1 is located on the left side of the vehicle, below the fender. Check your surroundings and determine your path of travel. This is generally while trying to make a U-Turn. Once stopped, It seems like it is engaged into gear again. For models with a hitch. Place shop towels beneath the oil filter 1. Before reusing, take the battery to your dealer for testing and recharging.
I generally use it at low speeds with a load behind it. I will attach pictures and a video here shortly. Performing the scheduled maintenance is very important. All information contained within this publication is based on the latest product information at the time of publication. Do not perform service on the spark arrestor while the system is hot.
Activate the starter for a maximum of five seconds, releasing the key when the engine starts. Dropped the guy an email and told him that there is no way that this machine would drive fine after the carb job like he said. Have an authorized Polaris dealer perform these services. Follow the instructions on the container for the recommended amounts. The load is never terribly heavy. A helmet can prevent a severe head injury.
Allow components to cool sufficiently before proceeding. Never store or use a partial bottle of brake fluid. To change gears, stop the vehicle, and with the engine idling, move the lever to the desired gear. Using a clean, dry cloth, clean the filter sealing surface on the crankcase. Water will enter the recoil housing if the starter handle is disengaged from the rope guide when under water. The shift lever and 4x4 switch do not move, of course. The front suspension in the Scrambler 400 is MacPherson strut, with 8.
Check the friction pads for wear, damage and looseness. Always remove the ignition key when the vehicle is not in use. Remove the taillight lens cover mounting screws. While we keep thousands of parts on-hand at our warehouse, there are over thousands more that we offer. See page 117 for the part numbers of Polaris products. Looks to me like there is a bent shift fork unless there is something else that causes that on a Polaris.
State of Voltage Charge 100% 12. Handlebars The handlebars can be adjusted for rider preference. Not that difficult but I made it so. See your Polaris dealer for engine heater kits, which provide quicker warm-ups and easier starting in colder weather. Check the amount of chain slack in three different locations by moving the vehicle slightly forward to gain slack at the top side of the rear chain. Apply the brakes slightly to aid in slowing, using the single brake lever. Determine water depths and current before crossing.