The display will indicate which signal mode is in effect. To install: Coat the threads on the sender with Teflon® tape or electrically conductive sealer, then install the sender. To clear the codes for the purposes of testing or confirming repair, perform the code reading procedure. To open the liftgate, rotate the handle clockwise and to open the liftgate window, rotate the handle counterclockwise. Roadtest the vehicle for proper operation. Drive or idle in neutral the vehicle for 4 minutes.
The Ford Explorer service manual will show you which tools to use and how simple it will be to perform a first oil change, spark plug change, or air filter swap. The following sections detail what each of these indicators means. When raising the vehicle on a hoist, position the front end adapters under the center of the lower suspension arm or the spring supports as near to the wheels as practical. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. Protect your skin by washing with soap and water. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
Wipe away any dirt in the area of the dipstick to prevent it from falling into the filler tube. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this owner guide. Remove the alternator adjusting arm and throttle body brace. Gasoline and gasoline-methanol blends may contain small amounts of carcinogens, such as benzene. It also includes any equipment that is standard on that model.
Matchmark the driveshaft end yoke and rear axle companion flange to assure proper positioning during assembly. Preparing Your Vehicle Your vehicle has a 12-volt starting system, so you need to use a 12-volt jumper system. Pull upward on the latch release handle at the side of the seatback, while pulling the seatback forward with the other hand. To install: Install a new gasket onto the sensor. Only use the accelerator when you have problems getting your vehicle started. Do not damage the sensing element or possible failure of the sensor may occur. Remove the pushrods, keeping them in order so they may be installed in their original locations.
Connect the shock absorber to the lower shock stud. Loosen the wheel nuts by pulling up on the handle of the lug nut wrench about one-half turn counterclockwise. If you ever lose your service manual just contact us we will send to you the service manual within 24 hours for free for lifetime. Install the valve covers using new gaskets. Engage the lens retaining tab. The door will open approximately one inch then it can be manually moved to the full open position.
Inspect the condition of the hose clamps and replace them, if necessary. Camshaft specifications are sometimes modified by Ford after production. Refer to Fuel pump shut-off switch in the Index to find additional information. Low Oil Level This warning message is displayed when your engine oil level is low. Unplug the wire harness from the bulb and either slide the retainer over the plug, or remove it from the bulb To install:. Make sure that the timing marks are still aligned.
Without doing this change, you'll receive an error message while trying to bring up a wiring diagram. Long-term exposure to unleaded gasoline vapors has caused cancer in laboratory animals. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. Rear window defroster switch To defrost the rear window: Clear any snow from the rear window. The normal 12 volt electrical system voltage could damage the meter! If you haven't already, apply a generous amount of penetrating oil or solvent to any rusted fasteners.
Follow towing instructions of a reputable rental agency. Lubricate all rocker arm assemblies with heavy engine oil. When descending a steep hill avoid sudden braking. For this reason, Ford has authorized its dealers to repair, at no charge to the owner,. Always use safety chains when towing.
For longer, trouble-free operation, keep the top of the battery clean and dry. To install: Thoroughly clean the gasket mating surfaces on the cover and the cylinder head. Make certain that the connectors are properly seated and all of the sealing rings are in place when connecting leads. © 2004 Thomson Delmar Learning. Interval wiper on turn signal lever To set the interval wipers, rotate the knob at the end of the turn signal lever toward or away from the instrument panel to the interval operation you desire. Refer to a local reputable machine shop as necessary. Do not drive your vehicle if it does not operate properly.
Supplemental air bag readiness light. Remove the nut retaining the half round yoke to the coupling shaft and remove the yoke. Some of the lights listed are optional. Raise and support the vehicle safely. Disconnect the negative battery cable. For a constant spray, keep the knob pushed in. If necessary, you can remove the cover if it is in your way Remove the heater core access panel attaching screws.